Jr Propo X 3810 Manual

понедельник 06 апреляadmin

R/CUSB-Interface for flight simulators

USB-Interface II and USB-Interface III

  • learn and train model flying without the danger of a crash, independent on weather daytime or your flight instructor

  • works with nearly all R/C transmitters (Graupner, Futaba, Multiplex, Hitec, Walkera, .)

  • works with nearly all R/C receivers (Graupner, Futaba, Multiplex and compatible)

  • runs with most simulators (FMS, Realflight G2, Piccofly, Easyfly, Aerofly, games, .)

  • no hand-soldered cheap schlock but machine-made goods of quality

  • simple installation, no driver needed

  • axis and buttons are programmable

  • future-proof due to updateable software, programmable with self-made software, SDK available

Jr propo x-3810 #64161. Por TONY45 - Sab, 21 May 2005 12:55 - Sab, 21 May 2005 12:55 #64161. Hola, tengo una emisora patatera y quiero pasarme a algo definitivo, que opinais de esta Jr. No tiene los permisos requeridos para ver los archivos adjuntos a este mensaje.

Overview

USB-Interface II

USB-Interface II with Fu6sq transmitter cord

Technical data USB-Interface II

The RC-USB-Interface has some enhancements compared to the Gameport Interface:

  • It can be used by modern notebooks equipped without gameport.

  • supports USB 1.1, USB 2.0, Hot-Plugging and is powered by USB

  • works with all transmitters: Though easily exchangeable transmitter cords, you can use one USB-Interface for different transmitters

  • Up to 9 RC channels are transmitted to the PC. Consequently, you can also control flaps, retractable landing gear, . in suited simultators with the R/C transmitter.

  • channel assignment: R/C channel 1 to 7 -> joystick axis 1 to 8, R/C channel 5 to 9 -> button 1 to 8

  • The small tremble of the model rudders (due to many analog-digital convertions:PPMA -> µcontroller AD -> RC-unit DA -> sound card AD -> simulator) is reduced by the completly digital working RC-USB-Interface (PPM A -> µcontroller AD -> USB client D -> USB host D -> simulator).

  • fast and precise digitalization with 256 steps

  • flashing control LED

  • The USB-Interface II is programmable: Assignment of axis and buttons, reaction of buttons can be reprogrammed quickly and easily.

  • since Okt. 2006 updatable firmware: The Interface is prepared to understand future transmission modes of new transmitters. (look for firmware updates in the Forum, e.g. Walkera PCM WK-0701, 3000 steps resolution, .)

Compatibility

After having installed the HID-driver (HID-driver, Windows included), the USB Interface is instantly ready for operation on Win98 SE, WinME, Win2000, WinXP (instruction manualusb-interface_en.pdf [210kB]), LINUX, Mac OS X (Screenshots osx.pdf [280kB]), . (in general: all O/S that support HID USB joysticks). It has a 2m cable and works with nearly all R/C transmitters equipped with a buddy box.

The USB Interface works with most R/C simulators that can be controlled by a normal joystick:

  • Aerofly 1.2x
  • Aerofly Pro(with original dongle)
  • Aerofly Pro Deluxe(with original dongle)
  • EasyFly
  • Flanker2.0
  • FMS
  • Microsoft Flight Simulator
  • PicoFly
  • Pre-Flight
  • RC/Helicopter
  • Realflight Deluxe
  • Realflight G2
  • ReVolt (RC-Car-simulation)
  • Big Scale Racing
  • X-Plane (Mac OS X)
  • FlightGear (LINUX)
  • ..

It doesn't work with Reflex, Reflex XTR or True-Flight.

Connectivity

interface name: USB-Int2

USB-Interface II with fixed receiver cord

USB-Interface II with fixed JR receiver cord

Technical data USB-Interface II with fixed receiver cord

Same data like USB-Interface II plus:

  • It can be connected with an R/C receiver. So a transmitter without buddy box or PPM signal can be made suitable for simulators. The USB-Interface supplys the receiver with power. It reads up to 4 R/C channels from the receiver.

  • Transmission up to 4 signals from the receiver

  • All transmitter cords to connect it with a R/C transmitter are usable

Connectivity

interface name: USB-Int2_R

Experience Voice Control film transcript(Ian uses Dictation with Voice Control)Wake up.MUSIC PLAYSThe level readings on the gray and white microphone-shaped Dictation icon move up and down with Ian’s voice.(Ian dictating)Voice Control is a breakthrough feature that gives you full control of your devices comma, with just your voice, period.Text of Ian’s dictation appears in Notes.(Ian dictating)It’s a whole new way to do everything you love, period. And because they are built from their iOS versions, they provide a seamless experience across your devices. Enjoy a broad range of Mac apps — from travel, entertainment, and gaming to banking, education, and project management. Download mac os x version 10.5.4 leopard server unlimited client.

RC USB-Interface III

USB-Interface III with JR3.5 receiver cord

Technical data RC USB-Interface III

RC USB-Interface II has the following enhancements compared to its predecessor:

  • It can be connected with an R/C receiver. So a transmitter without buddy box or PPM signal can be made suitable for simulators. The USB-Interface supplys the receiver with power. It reads up to 7 R/C channels from the receiver.

  • Optionally, a transmitter cord can be connected with the exchangeable receiver cord. The USB-Interface III is used with the R/C transmitter just like USB-Interface II. The source of the signal is detected automatically.

  • It has a 16 pin connector and its firmware is updatable. So it can be used as generic device for monitoring, sensor measurement, controlling, as USB dongle, migrating applications to USB, PPM analyzer, training, prototyping, ..

  • The Software Development Kit - USB-Interface III SDK is offered for free. It supports the development of new applications. Examples can be found in the Forum, e.g. PPM Generator (controlling a model via PC)

  • More information: data sheet usb-int3_datenblatt.pdf [180kB]

Compatibility

see USB-Interface II

Connectivity

Interface name: USB-Int3

Programming tool for R/C USB-Interface

The Interface is programmed with IntCon. The Assignment of axis and buttons can be chosen freely.

The program runs on Windows 98 to Windows XP.

This software and a brief instruction manual is here: software

Transmitter Cords

The USB-Interface hard- and software is designed to work with all transmitters. The Interface is equipped with a connector for transmitter cords fitting your individual buddy box. More information about buddy box pin assignment: buddy boxes

3,5 mm stereo jack plug

R/C vendor: Graupner / JR

transmitter: FM 314, mc-10, mc-12, mc-14, mc-15, mc-16, mc-16/20, mc-18, mc-20, mc-22, mc-24, mx-22, JR 9x, JR 347, FM4014 (pos. modulation), ..

JR (European RF part and buddy box): JR Quattro, JR 9x, X-347, X-387, X-388, X-756, X-3810, .

transmitter cord name: JR3.5

R/C vendor: Lexors

transmitter: Nova 4, Nova 4+1, Nova 6

transmitter cord name: Lex3.5

3,5 mm mono jack plug

R/C vendor: Futaba

transmitter: FC-28, FC-16, FC-18, 3PJ, T3PJ, T3PK, ..

transmitter cord name: Fu3.5

R/C vendor: Graupner/JR

hand held transmitters with DSC connector: MX-12, MX-22, .

JR (American RF part and buddy box): X-347, X-387, X-388, X-756, X-3810, .

transmitter cord name: Fu3.5

2,5 mm mono jack plug Russian commercial aircraft.

R/C vendor: Futaba

transmitter: FX-14, FX-15, FX-18, ..

transmitter cord name: Fu2.5

5-pin DIN plug

R/C vendor: Multiplex

transmitter: Pico-Line, mc1010, .

transmitter cord name: MPX5

R/C vendor: Robbe

transmitter: CM-Basic, (Terra Top), mc2015F, .

transmitter cord name: Ro5

R/C vendor: Sanwa

transmitter: (RD8000, RD6000, VG400, VG6000, Radiant, Vanguard PPM), .

transmitter cord name: Sa5

7-pin DIN plug

R/C vendor: Multiplex

transmitter: Pico-Line, EVO 9, Cockpit MM, mc3030, .

transmitter cord name: MPX7

6-pin DIN plug

R/C vendor: Futaba

transmitter: FC-16, FC-18+, FC-28, FF 7, .

transmitter cord name: Fu6DIN

R/C vendor: Hitec

transmitter: Laser 4, Flash, Eclipse, .

transmitter cord name: Fu6DIN

6-pin square plug

R/C vendor: Futaba

transmitter: 4C, 7C, 9C, FF 4, FF 7, FF 9, T6EXA, Skysport T4YF, .

transmitter cord name: Fu6sq

R/C vendor: Kyosho

transmitter: transmiter of Caliber 24

transmitter cord name: Fu6sq

special pin assignments

on request

Graupner MicroG

JR4DIN

Walkera PCM WK-0701

WK701-4DIN

Walkera 22E (35, 36, 39)

WK22E-4DIN

.

Receiver Cords

The USB-Interface 3 is connected with the servo connectors of R/C receivers or a transmitter cord via these receiver cords. Special pin assignments are possible.

Graupner/JR receiver cord

Receiver with Graupner/JR servo connectors

further R/C vendors with compatible connectors

receiver cord name: R-JR

Multiplex receiver cord

Receiver with Multiplex servo connectors

further R/C vendors with compatible connectors

receiver cord name: R-MPX

Futaba receiver cord

Receiver with Futaba servo connectors

further R/C vendors with compatible connectors

Walkera

receiver cord name: R-Fu

Development receiver cord

connects the USB-Interface 3 with periphery or PCBs for self-made applications

receiver cord name: R-Dev

Radio

Receiver Adapter

Receiver Adapter with Graupner/JR servo connectors

Equipped with the Receiver Adapter you don't need a buddy box connector on your R/C transmitter to use the USB Interface. The Receiver Adapter is connected with the R/C receiver. It reads out the individual servo positions and provides the PPM signal for the USB Interface 2.

  • uses up to 7 servo channels

  • operates with all R/C receivers, that support popular servos from Graupner/JR, Futaba or Multiplex

  • can be used in wireless master/slave trainer system in principle

Installation, hints

Windows

Quickstart USB-Interface: quickstart_de.pdf [ 260 kB], quickstart_en.pdf [ 260 kB], quickstart_it.pdf [ 260 kB]

Instruction manual USB-Interface:usb-interface.pdf [ + 1,4 MB]

Data sheet USB-Interface 3 usb-int3_datenblatt.pdf [180kB]

Mac OS X

Screenshots osx.pdf [280kB]

FAQ

(Flash Player 5 required)

JR X3810The JR X3810 is realy 3 radios in 1With its extensive list of specific software features for airplane, helicopter, and gliders, it's a radio that can handle your entire fleet of models and any you may be thinking of adding to it.The X-3810 was also designed with the notion that modellers would rather spend more of their time flying instead of programming their radio. As a result the X3810/XP8103 is loaded with sophisticated features that not only enhance your flying experience but simplify it as well.Whether your just getting into radio control or deep into it already, the JR X-3810 is one radio you will never outgrow. Please note that you need to specify Mode 1 or Mode 2. The TX is not Mode changeable because of the 3+1 digital trim technology.Look at the X-3810/XP8103 as an investment in your modelling future.3+1 Digital TrimsJR's 3+1 Digital Trim arrangement utilizes Advanced Digital Trims on the roll, pitch, and yaw channels and a mechanical trim lever on the throttle channel - the setup most preferred by modelers we spoke to.Auto Trim MemoryMoving the digital trim switches automatically stores the new trim position in memory for that model. This allows switching between model set ups without having to reset trim position each time and prevents accidental displacement of trim position when the radio is off.Adjustable Trim StepsThis allows servo adjustment of 1 to 10 steps per 'click' of the digital trim switches for fine or coarse adjustments of the trim position.Adjustable Trim Position TonesTrim position and direction of movement is audibly indicated with 'beeps' of varying frequency and tone whenever a digital trim switch is moved.